The simplest form of an expression is a *constant*.
There are 6 types of constants, corresponding to the 6 data
types. Here are some integer constants:

1 0 -100 32767 +15

Then we have real constants:

1.0 -0.25 2.0E6 3.333E-1

The E-notation means that you should multiply the constant by 10 raised to the power following the "E". Hence, 2.0E6 is two million, while 3.333E-1 is approximately one third.

For constants that are larger than the largest real allowed, or that requires high precision, double precision should be used. The notation is the same as for real constants except the "E" is replaced by a "D". Examples:

2.0D-1 1D99

Here 2.0D-1 is a double precision one-fifth, while 1D99 is a one followed by 99 zeros.

The next type is complex constants. This is designated by a pair of constants (integer or real), separated by a comma and enclosed in parentheses. Examples are:

(2, -3) (1., 9.9E-1)

The first number denotes the real part and the second the imaginary part.

The fifth type is logical constants. These can only have one of two values:

.TRUE. .FALSE.

Note that the dots enclosing the letters are required.

The last type is character constants. These are most often
used as an *array* of characters, called a *string*.
These consist of an arbitrary sequence of characters enclosed in
apostrophes (single quotes):

'ABC' 'Anything goes!' 'It is a nice day'

Strings and character constants are case sensitive. A problem arises if you want to have an apostrophe in the string itself. In this case, you should double the apostrophe:

'It''s a nice day'

The simplest non-constant expressions are of the form

operand operator operand

and an example is

x + y

The result of an expression is itself an operand, hence we can nest expressions together like

x + 2 * y

This raises the question of precedence: Does the last
expression mean `x + (2*y)` or `(x+2)*y`? The
precedence of arithmetic operators in Fortran 77 are (from
highest to lowest):

**{exponentiation}*,/{multiplication, division}+,-{addition, subtraction}

All these operators are calculated left-to-right, except the exponentiation operator **, which has right-to-left precedence. If you want to change the default evaluation order, you can use parentheses.

The above operators are all binary operators. there is also
the unary operator `-` for negation, which takes
precedence over the others. Hence an expression like `-x+y`
means what you would expect.

Extreme caution must be taken when using the division operator, which has a quite different meaning for integers and reals. If the operands are both integers, an integer division is performed, otherwise a real arithmetic division is performed. For example, 3/2 equals 1, while 3./2. equals 1.5 (note the decimal points).

The assignment has the form

variable_name=expression

The interpretation is as follows: Evaluate the right hand side and assign the resulting value to the variable on the left. The expression on the right may contain other variables, but these never change value! For example,

area = pi * r**2

does not change the value of `pi` or `r`, only `area`.

When different data types occur in the same expression, *type
conversion* has to take place, either explicitly or
implicitly. Fortran will do some type conversion implicitly. For
example,

real x x = x + 1

will convert the integer one to the real number one, and has the desired effect of incrementing x by one. However, in more complicated expressions, it is good programming practice to force the necessary type conversions explicitly. For numbers, the following functions are available:

int real dble ichar char

The first three have the obvious meaning. `ichar` takes
a character and converts it to an integer, while `char`
does exactly the opposite.

Example: How to multiply two real variables `x` and `y`
using double precision and store the result in the double
precision variable `w`:

w = dble(x)*dble(y)

Note that this is different from

w = dble(x*y)

*Copyright © 1995-7 by Stanford University. All rights
reserved.*