Nikolaus Hammler

From Murmann Mixed-Signal Group

(Difference between revisions)
Jump to: navigation, search
Line 11: Line 11:
== Low-Rate Linearization of Power Amplifiers  ==
== Low-Rate Linearization of Power Amplifiers  ==
-
The last component of a wireless transmission system is usually the '''power amplifier''' (PA). Its task is to amplify the signal to be transmitted to drive the antenna. However, operating the power amplifier in the linear region results in poor efficiency. For this reason, PAs are often operated in their '''nonlinear region''', near the saturation. The price paid for the better efficiency is distortion and spectral regrowth of the signal due to the nonlinear behavior. This distortion is often not acceptable. A common approach to diminish this effect is to use a '''predistorter''' (PD). The PD distorts the original input signal in a nonlinear way, such that the overall transfer function is '''linear again'''. However, since the behavior of the PA changes during operation (due to self-heating, biasing networks etc.) it is necessary to continuously determine the appropriate PD. The general setup looks as follows:  
+
The last component of a wireless transmission system is usually the '''power amplifier''' (PA). Its task is to amplify the signal to be transmitted to drive the antenna. However, operating the power amplifier in the linear region results in poor efficiency. For this reason, PAs are often operated in their '''nonlinear region''', near the saturation. The price paid for the better efficiency is distortion and spectral regrowth of the signal due to the nonlinear behavior. This distortion is often not acceptable. A common approach to diminish this effect is to use a '''predistorter''' (PD). The PD distorts the original input signal in a nonlinear way, such that the overall transfer function is '''linear again'''. However, since the behavior of the PA changes during operation (due to self-heating or aging) it is necessary to continuously determine the appropriate PD. The general setup looks as follows:  
[[Image:Papd.png|center|300px|Papd.png]]  
[[Image:Papd.png|center|300px|Papd.png]]  

Revision as of 10:28, 3 August 2013

Niki.jpg


Research areas: Low-rate sampling, low-rate system identification, digital predistortion

Email: nhammler AT stanford DOT edu


Low-Rate Linearization of Power Amplifiers

The last component of a wireless transmission system is usually the power amplifier (PA). Its task is to amplify the signal to be transmitted to drive the antenna. However, operating the power amplifier in the linear region results in poor efficiency. For this reason, PAs are often operated in their nonlinear region, near the saturation. The price paid for the better efficiency is distortion and spectral regrowth of the signal due to the nonlinear behavior. This distortion is often not acceptable. A common approach to diminish this effect is to use a predistorter (PD). The PD distorts the original input signal in a nonlinear way, such that the overall transfer function is linear again. However, since the behavior of the PA changes during operation (due to self-heating or aging) it is necessary to continuously determine the appropriate PD. The general setup looks as follows:

Papd.png

Prevalent approaches sample the output signal y(t) at the Nyquist rate. However, advanced technologies such as LTE Advanced require bandwidths of 100 MHz and more. Together with the spectral regrowth, this results in sampling rates in the Gigahertz range, placing a high burden on the ADC.

On the other hand, PAs are usually modelled using a model with only few degrees of freedom. For example, a typical class AB amplifier can be modelled with a Memory Polynomial (MP, a truncated Volterra series) having as few as 20 coefficients. The motivating question "Do we really need to sample at this high rate just to obtain a few coefficients?" is similar as in Compressive Sampling or Finite Rate of Innovation (FRI). Based on the ideas from FRI, we propose an inverse modeling approach:

  1. Identify the PA (system H) at a low rate using ideas from FRI. The sampling rate relates to the degrees of freedom in the PA model, rather than the Nyquist rate
  2. Invert the estimated system to obtain the PD, H-1

The block diagram of this scheme is shown below:

Papd2.png
Personal tools