ANSYS
From FarmShare
Contents |
ANSYS
ANSYS v14.5
ANSYS v14.5 is installed. Update v14.5.1 is applied. To use it, try 'module avail' and module load ansys and 'which ansys145'.
but if you executed the 'module load ansys' command, you should be able to just type ansys145 or launcher145.
In the launcher program, if you need to choose a license, use "ANSYS Academic Research".
running the workbench
To run the ansys workbench, load the module and run runwb2. Since the workbench is heavy graphics, we would recommend you run it inside a VNC session. See FarmVNC. If you need accelerated 3D graphics, you can run similar to the example here: smokeParticles on Rye.
module load ansys runwb2
Fluent
You can bring up fluent by simply running fluent binary
module load ansys fluent
ansys v14.5 example
In this example, ansys is run in batch mode with an input command file. It produces file000.png which should look like the image here in this wiki.
$ module load ansys $ mkdir ansystest $ cd ansystest $ ansys145 < /farmshare/software/examples/ansys/example1.cmd ANSYS Academic Teaching Advanced *------------------------------------------------------------------* | | | W E L C O M E T O T H E A N S Y S (R) P R O G R A M | | | *------------------------------------------------------------------* *************************************************************** * ANSYS 14.5 LEGAL NOTICES * *************************************************************** * * * Copyright 2012 SAS IP, Inc. All rights reserved. * * Unauthorized use, distribution or duplication is * * prohibited. * * * * Ansys is a registered trademark of ANSYS, Inc. or its * * subsidiaries in the United States or other countries. * * See the ANSYS, Inc. online documentation or the ANSYS, Inc. * * documentation CD or online help for the complete Legal * * Notice. * * * *************************************************************** * * * THIS ANSYS SOFTWARE PRODUCT AND PROGRAM DOCUMENTATION * * INCLUDE TRADE SECRETS AND CONFIDENTIAL AND PROPRIETARY * * PRODUCTS OF ANSYS, INC., ITS SUBSIDIARIES, OR LICENSORS. * * The software products and documentation are furnished by * * ANSYS, Inc. or its subsidiaries under a software license * * agreement that contains provisions concerning * * non-disclosure, copying, length and nature of use, * * compliance with exporting laws, warranties, disclaimers, * * limitations of liability, and remedies, and other * * provisions. The software products and documentation may be * * used, disclosed, transferred, or copied only in accordance * * with the terms and conditions of that software license * * agreement. * * * * ANSYS, Inc. is a UL registered * * ISO 9001:2008 company. * * * *************************************************************** * * * This product is subject to U.S. laws governing export and * * re-export. * * * * For U.S. Government users, except as specifically granted * * by the ANSYS, Inc. software license agreement, the use, * * duplication, or disclosure by the United States Government * * is subject to restrictions stated in the ANSYS, Inc. * * software license agreement and FAR 12.212 (for non-DOD * * licenses). * * * *************************************************************** AFTER YOU HAVE READ, UNDERSTOOD, AND AGREED TO THE PREVIOUS NOTICES, PRESS <CR> OR <ENTER> TO CONTINUE ***** ANSYS COMMAND LINE ARGUMENTS ***** DESIGNXPLORER REQUESTED 00670021 VERSION=LINUX x64 RELEASE= 14.5 UP20120918 CURRENT JOBNAME=file 14:57:00 FEB 13, 2013 CP= 0.192 RUN SETUP PROCEDURE FROM FILE= /farmshare/software/non-free/ANSYS-install/v145/ansys/apdl/start145.ans /INPUT FILE= /farmshare/software/non-free/ANSYS-install/v145/ansys/apdl/start145.ans LINE= 0 BEGIN: 1 /BATCH,LIST,COPY 2 /graphics,power 3 /show,png 4 5 /title, Simple Conduction Example 6 /PREP7 7 8 ! define geometry 9 10 length=1.0 11 height=1.0 12 blc4,0,0,length, height ! area - one corner, then width and height 13 14 ! mesh 2D areas 15 16 ET,1, PLANE55 ! Thermal element only 17 MP,KXX,1,10 ! 10 W/mC 18 ESIZE,length/20 ! number of element sub-divisions/side 19 AMESH,ALL 20 21 FINISH 22 /SOLU 23 24 ANTYPE,0 ! STEADY-STATE THERMAL ANALYSIS 25 26 ! fixed temp BCs 27 NSEL,S,LOC,Y,height ! select nodes on top with y=height 28 D,ALL,TEMP,500 ! apply fixed temp of 500C 29 NSEL,ALL 30 NSEL,S,LOC,X,0 ! select nodes on three sides 31 NSEL,A,LOC,X,length 32 NSEL,A,LOC,Y,0 33 D,ALL,TEMP,100 ! apply fixed temp of 100C 34 NSEL,ALL 35 36 SOLVE 37 FINISH 38 39 /POST1 40 PLNSOL,TEMP,,0, ! contour plot of temperatures Use PowerGraphics for solid and shell elements *** NOTE *** CP = 0.292 TIME= 14:57:03 Facet level set to 1 for maximum speed Use /EFACET,2 for curved boundaries. /SHOW SWITCH PLOTS TO PNG - RASTER MODE. TITLE= Simple Conduction Example 1 ***** ANSYS - ENGINEERING ANALYSIS SYSTEM RELEASE 14.5 ***** ANSYS Academic Teaching Advanced 00670021 VERSION=LINUX x64 14:57:03 FEB 13, 2013 CP= 0.296 Simple Conduction Example ***** ANSYS ANALYSIS DEFINITION (PREP7) ***** PARAMETER LENGTH = 1.000000000 PARAMETER HEIGHT = 1.000000000 CREATE A RECTANGULAR AREA WITH X-DISTANCES FROM 0.000000000 TO 1.000000000 Y-DISTANCES FROM 0.000000000 TO 1.000000000 OUTPUT AREA = 1 ELEMENT TYPE 1 IS PLANE55 2-D THERMAL SOLID KEYOPT( 1- 6)= 0 0 0 0 0 0 KEYOPT( 7-12)= 0 0 0 0 0 0 KEYOPT(13-18)= 0 0 0 0 0 0 CURRENT NODAL DOF SET IS TEMP TWO-DIMENSIONAL MODEL MATERIAL 1 KXX = 10.00000 DEFAULT ELEMENT DIVISIONS PER LINE BASED ON ELEMENT SIZE = 0.500E-01 GENERATE NODES AND ELEMENTS IN ALL SELECTED AREAS ** AREA 1 MESHED WITH 400 QUADRILATERALS, 0 TRIANGLES ** NUMBER OF AREAS MESHED = 1 MAXIMUM NODE NUMBER = 441 MAXIMUM ELEMENT NUMBER = 400 ***** ROUTINE COMPLETED ***** CP = 0.312 ***** ANSYS SOLUTION ROUTINE ***** PERFORM A STATIC ANALYSIS THIS WILL BE A NEW ANALYSIS SELECT FOR ITEM=LOC COMPONENT=Y BETWEEN 1.0000 AND 1.0000 KABS= 0. TOLERANCE= 0.500000E-02 21 NODES (OF 441 DEFINED) SELECTED BY NSEL COMMAND. SPECIFIED CONSTRAINT TEMP FOR SELECTED NODES 1 TO 441 BY 1 REAL= 500.000000 IMAG= 0.00000000 ALL SELECT FOR ITEM=NODE COMPONENT= IN RANGE 1 TO 441 STEP 1 441 NODES (OF 441 DEFINED) SELECTED BY NSEL COMMAND. SELECT FOR ITEM=LOC COMPONENT=X BETWEEN 0.0000 AND 0.0000 KABS= 0. TOLERANCE= 0.100000E-05 21 NODES (OF 441 DEFINED) SELECTED BY NSEL COMMAND. ALSO SELECT FOR ITEM=LOC COMPONENT=X BETWEEN 1.0000 AND 1.0000 KABS= 0. TOLERANCE= 0.500000E-02 42 NODES (OF 441 DEFINED) SELECTED BY NSEL COMMAND. ALSO SELECT FOR ITEM=LOC COMPONENT=Y BETWEEN 0.0000 AND 0.0000 KABS= 0. TOLERANCE= 0.100000E-05 61 NODES (OF 441 DEFINED) SELECTED BY NSEL COMMAND. SPECIFIED CONSTRAINT TEMP FOR SELECTED NODES 1 TO 441 BY 1 REAL= 100.000000 IMAG= 0.00000000 ALL SELECT FOR ITEM=NODE COMPONENT= IN RANGE 1 TO 441 STEP 1 441 NODES (OF 441 DEFINED) SELECTED BY NSEL COMMAND. ***** ANSYS SOLVE COMMAND ***** 1 ***** ANSYS - ENGINEERING ANALYSIS SYSTEM RELEASE 14.5 ***** ANSYS Academic Teaching Advanced 00670021 VERSION=LINUX x64 14:57:04 FEB 13, 2013 CP= 0.316 Simple Conduction Example S O L U T I O N O P T I O N S PROBLEM DIMENSIONALITY. . . . . . . . . . . . .2-D DEGREES OF FREEDOM. . . . . . TEMP ANALYSIS TYPE . . . . . . . . . . . . . . . . .STATIC (STEADY-STATE) GLOBALLY ASSEMBLED MATRIX . . . . . . . . . . .SYMMETRIC *** NOTE *** CP = 0.320 TIME= 14:57:04 Present time 0 is less than or equal to the previous time. Time will default to 1. *** NOTE *** CP = 0.320 TIME= 14:57:04 The conditions for direct assembly have been met. No .emat or .erot files will be produced. L O A D S T E P O P T I O N S LOAD STEP NUMBER. . . . . . . . . . . . . . . . 1 TIME AT END OF THE LOAD STEP. . . . . . . . . . 1.0000 NUMBER OF SUBSTEPS. . . . . . . . . . . . . . . 1 STEP CHANGE BOUNDARY CONDITIONS . . . . . . . . NO PRINT OUTPUT CONTROLS . . . . . . . . . . . . .NO PRINTOUT DATABASE OUTPUT CONTROLS. . . . . . . . . . . .ALL DATA WRITTEN FOR THE LAST SUBSTEP SOLUTION MONITORING INFO IS WRITTEN TO FILE= file.mntr Range of element maximum matrix coefficients in global coordinates Maximum = 6.66666667 at element 78. Minimum = 6.66666667 at element 2. *** ELEMENT MATRIX FORMULATION TIMES TYPE NUMBER ENAME TOTAL CP AVE CP 1 400 PLANE55 0.040 0.000100 Time at end of element matrix formulation CP = 0.500032008. SPARSE MATRIX DIRECT SOLVER. Number of equations = 361, Maximum wavefront = 6 Memory allocated for solver = 15.259 MB Memory required for in-core = 0.162 MB Optimal memory required for out-of-core = 0.098 MB Minimum memory required for out-of-core = 0.091 MB *** NOTE *** CP = 0.552 TIME= 14:57:32 The Sparse Matrix solver is currently running in the in-core memory mode. This memory mode uses the most amount of memory in order to avoid using the hard drive as much as possible, which most often results in the fastest solution time. This mode is recommended if enough physical memory is present to accommodate all of the solver data. Sparse solver maximum pivot= 26.6666667 at node 378 TEMP. Sparse solver minimum pivot= 14.8603497 at node 359 TEMP. Sparse solver minimum pivot in absolute value= 14.8603497 at node 359 TEMP. *** ELEMENT RESULT CALCULATION TIMES TYPE NUMBER ENAME TOTAL CP AVE CP 1 400 PLANE55 0.044 0.000110 *** NODAL LOAD CALCULATION TIMES TYPE NUMBER ENAME TOTAL CP AVE CP 1 400 PLANE55 0.008 0.000020 *** LOAD STEP 1 SUBSTEP 1 COMPLETED. CUM ITER = 1 *** TIME = 1.00000 TIME INC = 1.00000 NEW TRIANG MATRIX *** ANSYS BINARY FILE STATISTICS BUFFER SIZE USED= 16384 0.062 MB WRITTEN ON ASSEMBLED MATRIX FILE: file.full 0.688 MB WRITTEN ON RESULTS FILE: file.rth FINISH SOLUTION PROCESSING ***** ROUTINE COMPLETED ***** CP = 0.716 1 ***** ANSYS - ENGINEERING ANALYSIS SYSTEM RELEASE 14.5 ***** ANSYS Academic Teaching Advanced 00670021 VERSION=LINUX x64 14:57:38 FEB 13, 2013 CP= 0.724 Simple Conduction Example ***** ANSYS RESULTS INTERPRETATION (POST1) ***** *** NOTE *** CP = 0.724 TIME= 14:57:38 Reading results into the database (SET command) will update the current displacement and force boundary conditions in the database with the values from the results file for that load set. Note that any subsequent solutions will use these values unless action is taken to either SAVE the current values or not overwrite them (/EXIT,NOSAVE). DISPLAY NODAL SOLUTION, ITEM=TEMP COMP= CUMULATIVE DISPLAY NUMBER 1 WRITTEN TO FILE file000.png - RASTER MODE. DISPLAY TITLE= Simple Conduction Example ***** END OF INPUT ENCOUNTERED ***** NUMBER OF WARNING MESSAGES ENCOUNTERED= 0 NUMBER OF ERROR MESSAGES ENCOUNTERED= 0 ***** PROBLEM TERMINATED BY INDICATED ERROR(S) OR BY END OF INPUT DATA ***** *** NOTE *** libpng version 1.0.8 - July 24, 2000 Copyright (c) 1998-2000 Glenn Randers-Pehrson Copyright (c) 1996, 1997 Andreas Dilger Copyright (c) 1995, 1996 Guy Eric Schalnat, Group 42, Inc. ZLIB Version 1.1.3 Copyright (C) 1995-1998 Jean-loup Gailly and Mark Adler +--------------------- A N S Y S S T A T I S T I C S ------------------------+ Release: 14.5 Build: UP20120918 Platform: LINUX x64 Date Run: 02/13/2013 Time: 14:57 Processor Model: Quad-Core AMD Opteron(tm) Processor 2384 Compiler: Intel(R) FORTRAN Compiler Version 11.1.0 (Build: 20100203) Intel(R) C/C++ Compiler Version 11.1.0 (Build: 20100203) Intel(R) Math Kernel Library Version 10.3.3 Product Build 20110314 Total number of cores available : 8 Number of physical cores available : 8 Number of cores requested : 2 (Shared Memory Parallel) GPU Acceleration: Not Requested Job Name: file Working Directory: /farmshare/user_data/bishopj/ansystest Total CPU time for main thread : 0.8 seconds Total CPU time summed for all threads : 1.1 seconds Elapsed time spent pre-processing model (/PREP7) : 0.4 seconds Elapsed time spent solution - preprocessing : 0.2 seconds Elapsed time spent computing solution : 27.1 seconds Elapsed time spent solution - postprocessing : 0.0 seconds Elapsed time spent post-processing model (/POST1) : 0.0 seconds Equation solver effective I/O rate : 0.6 MB/sec Maximum total memory used : 21.0 MB Maximum total memory allocated : 1088.0 MB Maximum total memory available : 31 GB +------------------ E N D A N S Y S S T A T I S T I C S -------------------+ *---------------------------------------------------------------------------* | | | ANSYS RUN COMPLETED | | | |---------------------------------------------------------------------------| | | | Release 14.5 UP20120918 LINUX x64 | | | |---------------------------------------------------------------------------| | | | Database Requested(-db) 512 MB Scratch Memory Requested 512 MB | | Maximum Database Used 1 MB Maximum Scratch Memory Used 20 MB | | | |---------------------------------------------------------------------------| | | | CP Time (sec) = 1.080 Time = 14:57:40 | | Elapsed Time (sec) = 46.000 Date = 02/13/2013 | | | *---------------------------------------------------------------------------* $ ls -l total 876 -rw-r--r-- 1 bishopj root 1979 Feb 13 14:57 file.BCS -rw-r--r-- 1 bishopj root 67 Feb 13 14:56 file.err -rw-r--r-- 1 bishopj root 65536 Feb 13 14:57 file.esav -rw-r--r-- 1 bishopj root 65536 Feb 13 14:57 file.full -rw-r--r-- 1 bishopj root 161 Feb 13 14:57 file.log -rw-r--r-- 1 bishopj root 721 Feb 13 14:57 file.mntr -rw-r--r-- 1 bishopj root 720896 Feb 13 14:57 file.rth -rw-r--r-- 1 bishopj root 149 Feb 13 14:57 file.stat -rw-r--r-- 1 bishopj root 20783 Feb 13 14:57 file000.png $ display file000.png
reference
static page: https://itservices.stanford.edu/service/sharedcomputing/software/ansys
HFSS
HFSS is technically an "ANSOFT" software, and ANSOFT was purchased by ANSYS, but the license manager software is slightly different, so you need to connect to port 44657 for lmgrd and port 59758 for ansoftd. If it only asks for one port, use the latter.
Windows ANSYS client license settings
You need to set host license3 and license port to 27035 (instead of the default 1055). Make sure to run the License Manager utility "as Administrator".
Getting support
You can create an ANSYS support account on their site and they will answer ANSYS-specific questions.